CEOInterviews.AI
Start App
Lars Moravy
Vice President of Vehicle Engineering, Tesla, Inc.

The FLYING Tesla Roadster explained by the man who engineered it

📅 Oct 16, 2026 Hagerty 27 MIN 2480277 VIEWS 122 SEGMENTS · 2 SPEAKERS
You’ve probably seen by now, that the new Tesla Roadster can fly. And flip. And drive upside down. But how does it do all that? Henry Catchpole met up with Lars Moravy, VP for Vehicle Engineering at Tesla, to talk through all the details of the long awaited new car and see how Optimus and SpaceX helped. Flying aside, a few things have changed since a new Roadster was teased by Elon Musk over a decade ago. For a start, it is now a two-seater, rather than a 2+2 and the styling, by Franz von Holzhausen, is much sleeker and more in-keeping with traditional supercar wedges. We particularly like th...

What Lars Moravy said

Written from the verified transcript and checked against it. Every figure links to the moment it was said.

Lars Moravy, Tesla's VP of vehicle engineering, explained the new Tesla Roadster to Hagerty's Henry Catchpole. He revealed it is rear-wheel drive with two power-dense motors producing over a megawatt and more torque than a Plaid. The car uses a unique 4680 aluminum cell with double-sided cooling for consistent performance and fast charging. Moravy stated the car weighs just under 1,700 kilos, countering the trend of heavy EVs. He detailed advanced aero including active barge boards and a wing creating up to 2g of downforce, plus a 'sucker system' with four fans that can hold over 2g in corners. The SpaceX package adds cold gas thrusters using nitrogen, enabling 0-60 mph in 0.55 seconds. Moravy confirmed the thrust produces over 80 kN, similar to a fighter jet. He mentioned the flight system with additional thrusters and that development prototypes exist, with a bigger build early next year.

Key takeaways

  1. The Roadster is rear-wheel drive with two motors producing over a megawatt and more torque than a Plaid.
  2. The car weighs just under 1,700 kilos, emphasizing lightweight design.
  3. The sucker system with four fans can hold over 2g in corners, breaking tire physics.
  4. The SpaceX package enables 0-60 mph in 0.55 seconds using cold gas thrusters.
  5. The thrust from the cold gas system is over 80 kN, comparable to a fighter jet engine.

Numbers and commitments

FigureWhat it refers toTypeAt
over 1400 Nm torque output of the motors metric 3:00
just under 1,700 kilos weight of the Roadster metric 4:28
over 200 miles per hour speed at which downforce is generated metric 12:21
2gs downforce generated at high speed metric 12:21
over 2gs cornering force in sucker mode metric 13:34
0.55 seconds 0-60 mph time for the thrust model metric 15:42
over 80 kN thrust produced by the cold gas system metric 16:03
10,000 PSI pressure capacity of the carbon overwrapped pressure vessel metric 15:16
200 L volume of the pressure vessel in the standard SpaceX package metric 15:16

Chapters

  1. 0:00Rear-wheel drive and powertrain
  2. 3:19Battery and cooling system
  3. 4:23Weight and chassis
  4. 6:17Inverters and drivetrain
  5. 8:05Thermal system and suspension
  6. 9:01Aero and active surfaces
  7. 12:38Sucker system and fans
  8. 15:16SpaceX cold gas thrusters
  9. 17:28Flight system and thrusters
  10. 23:24Development and future plans

Questions asked in this interview

5
  1. 4:26What are we going to say?
  2. 10:01That's the sort of almost the limiting factor, isn't it?
  3. 12:08So have you got any, again I feel like we're burying the lead here but kind of, but as a sort of conventional aero, have you got any figures for kind of like how much kind of downforce it's creating?
  4. 17:33So it becomes a single seater in there, right?
  5. 20:17In fact, want to have a closer look?
Henry Catchpole 0:23 ↗
This is the new Tesla Roadster. One of the most extraordinary cars, if we can still call it a car, that the world has ever seen. From cold gas thrusters to robot actuators, we've got all the details.
In all my time as a motoring journalist, I've never been on a launch quite like this. The day before the big reveal, I was driven mostly autonomously through Texas and then blindfolded for the last few miles.
The feeling of being in some elaborate magic trick didn't subside when the mask came off again. The car still hidden in a big black curtain box inside a vast pristine white SpaceX hangar.
And then it was there with a light bar like KITT glowing under the cover. Oh wow. Covers off to reveal the design by Franz von Holzhausen. A clear cousin of the Cybertruck, but in a package perhaps more befitting to the style. With its white panels and sharp lines, it looked part aerospace, part origami.
But the real curiosity remained, just what was underneath the skin. This is Lars Moravy, genuine car guy. He likes a restomod just the same as the rest of us. And also Tesla's vice president of vehicle engineering. And as he talked me through the new Tesla Roadster's secrets, he said some things that genuinely left me speechless.
Just a brief pause in the madness of flying cars to say that this film is driven by Hagerty. So if you need insurance for a special car that you don't drive every day, then take a trip to hagerty.com/henry.
Lars Moravy 2:41 ↗
First thing I guess I'll say because it's a bit of a surprise. It's only rear wheel drive.
Henry Catchpole 2:45 ↗
That was a big surprise to me. Yeah, that's...
I mean, we've been building all-wheel drive performance cars for a long time now, since probably 2014. There's something visceral, there's something emotional about having all that torque behind you. And there's two motors back there.
Lars Moravy 3:00 ↗
They're pretty power dense. You know, we have over a megawatt of power. You know, over 1400 Nm of torque. And that means that this motor, even though there's only two, actually has more torque and power than a Plaid.
Henry Catchpole 3:13 ↗
And they're all going through the rear wheels. So, we obviously had to beef those up. There's a lot of rubber back there.
Lars Moravy 3:19 ↗
That's like one of the first things that, you know, we really pushed on to make it, you know, the driver's car that we wanted. It's still kind of traditional in a Tesla sense where we put the battery underneath. So, this one has a unique cell that we developed in-house. It's our 4680 cell, but it's got a lot of cool features. You know, typically with a cylindrical cell, and again we can look at this, like you have a cooling tube that goes through the middle and you kind of cool from the one side out, but like what we realized is like to get the thermal performance we need, the repeatability, like the, you know, the driveability, the trackability, you know, just like making it feel like there's never power loss.
Henry Catchpole 3:51 ↗
Yeah.
Lars Moravy 3:51 ↗
We went to double-sided cooling and then it turns out, you know, we can really really increase the cooling power so that that battery just like stays level performance almost all the way through its drive life cycle. And on the charging side, um, you know, we can charge super fast. So, you know, I think when we did the middle Roadster, we were like, 'Oh, we're going to put all this range in it so you can get all this power.' And we kind of went back and said like, 'This car needs to be lightweight. It needs to be like a driver's car.' And driver's cars aren't 2,000 kilos, not even 1,800 kilos.
Henry Catchpole 4:23 ↗
So, what is this?
Lars Moravy 4:24 ↗
I'm still... We're still getting the final numbers here, but I'm...
Henry Catchpole 4:26 ↗
Ballpark. What are we going to say?
Lars Moravy 4:28 ↗
Just under 1,700 kilos.
Henry Catchpole 4:29 ↗
Okay. Wow.
This was something that I really hadn't expected and was a genuinely nice surprise. Even the little original Tesla Roadsters weighed around 1,300 kilos. And this is a significantly bigger, more sophisticated car with a much larger battery. And while we're talking about the battery, it seems like a good time to show you what it looks like.
Lars Moravy 4:50 ↗
The powertrain. This is, you know, everything we've learned at Tesla for 20 plus years of making, you know, electric vehicles put into one. Um, we have our 4680 cells here. Um these are special cells, special chemistry just for this to get that high power throughput. But they also have something cool on them. Most cylindrical... these are not steel. These are aluminum. Aluminum can. And the reason for that is um twofold. One, it's lighter. The other one is it's actually a little bit better at dissipating heat. So we have our cooling system with the double-sided cooling with...
Henry Catchpole 5:23 ↗
Jackets.
Lars Moravy 5:24 ↗
These jackets along either side. You know, you get your coolant that comes through here and it goes kind of in this, you know, downflow one side to the other, which does a couple things there. Once we pump all the coolant in from one side, you know, we're able to like keep a very uniform um heat flux throughout the battery because we're pushing cold to hot. And a lot of our batteries, we go, you know, down and back and reverse.
Henry Catchpole 5:47 ↗
Yeah. So, this is flux...
Lars Moravy 5:48 ↗
But this is just like flush it through one time, get it cool again, and come back. And that's kind of a unique thing here. Um, we have a titanium upper plate which nominally is usually steel. So we titanium a little bit higher specific heat capacity. We get the same thermal protection but thinner, lighter. Um, and we even tailor welded it here for the different thicknesses based on the different requirements across the pack itself. And then we have our typical aluminum lower plate. That's for dent resistance, impact resistance, but also for thermal management in a safety event.
Henry Catchpole 6:17 ↗
Then high voltage back here.
Lars Moravy 6:19 ↗
Yeah. So you got to take the DC power um get it out of the pack and then put it through the inverters to create the AC. So this is our power conversion system. This is running at that, you know, higher voltage 800 volt range like we do on Cybertruck and Semi. Um that's two reasons. One, that means we can charge at a higher voltage, you know, and get that 10-minute charge time. But two, also we get a little bit more efficiency in the power to discharge. So again this motor is super tiny like it's actually smaller than the Plaid motor. Um, we have the two motor rotor stator combos in here and you have a planetary gear set out here and that goes out there. So, no differential, independent control, right? The planetary gear set just with a 8.4 reduction out to the side helps us keep it super tight, super lightweight, you know, as I said before. Um, it's got, you know, more power and more torque than the three motors combined in a Plaid. And we're able to do that in a super tight package, which is really a testament to all the learning we've had over the years. And you just got independent inverters here. A little bit of redundancy, but also just to make sure each motor gets its own power. Cool thing about the inverters, we'll talk about later or another time. Um, we had to do some work in there to really suck the power out. Okay, but that's for a future date. Okay, got to save some secrets.
Henry Catchpole 7:32 ↗
One of those secrets for now is exactly how many kilowatt hours the battery is. What we do know is that the range is claimed to be over 300 miles and it's the fastest charging battery Tesla has ever produced with the aim being to go from 15 to 80% in just 10 minutes.
Lars Moravy 7:50 ↗
You know, we're hoping then that that means you get, you know, 25, 30 minutes of unlimited track performance and you come back in, recharge, you can do a track day and you can do it all day.
Henry Catchpole 7:58 ↗
You as a driver is going to take longer to recharge the car. Go out on a track, 20 minutes is like a lot for normal people.
Lars Moravy 8:05 ↗
Like you'll notice the cockpit comes up all to here. And so all of the, you know, thermal system suspension is, you know, hidden under here. Very traditional kind of supercar suspension, double wishbone, rocker arm. And then the cool thing is the thermal system, you know, we're using is sort of we've been developing our own thermal systems for a while. Um, and it's kind of the next integration sort of indirect the thermal system uses our like coolant base loop and we're able to get like a lot of efficiency gains out of that not only in the battery and power chain but also in cabin heating and cooling. So it's kind of our next generation of heat pump. So that's all stocked up here. Um, and then in the back, you know, you've got, you can't see, but underneath here, you've got those two motors we were talking about with independent inverters, a planetary gear set that's all mounted to a subframe, you know, within a multi-link rear suspension to kind of deal with all that torque.
Henry Catchpole 9:01 ↗
There are spool valve adaptive dampers, and the track mode will drop the ride height by 40 mm, increasing stiffness three-fold in the process. The body on this prototype is all carbon fiber, although some panels on the production models may be metal if needed. We'll get to the movable aero aspects of the bodywork in a second, but first we need to mention the headlights, which are not pop-up, but pop-down.
Lars Moravy 9:24 ↗
We've been developing kind of headlight modules for a while, but you know, this is a really slim headlight module. It's only maybe like 15 mm. We have the low beam and the high beam in one module and then you can imagine the design discussions to get the beam pattern to get out this like pop-down and get it out in the front. But um you know like there's a lot of nostalgia in this car and this is kind of one of those things where it's like yeah you could have pop-up headlights but pop-down's kind of cooler. You'll notice there's a panel up here just above the hood.
Henry Catchpole 9:51 ↗
Yeah.
Lars Moravy 9:52 ↗
That's actually an active vent for the cooling system to let you know more air out cuz at the rear of the car you can always put a wing on.
Henry Catchpole 9:58 ↗
Yeah.
Lars Moravy 9:59 ↗
Super easy. Yeah, front is always the difficult.
Henry Catchpole 10:01 ↗
That's the sort of almost the limiting factor, isn't it? That kind of...
Lars Moravy 10:04 ↗
And then of course like the styling and they always want it to be clean and look, you know, so yeah, we have this like chin spoiler that adds a lot. But inside here, which is difficult to see...
Henry Catchpole 10:12 ↗
Yeah.
Lars Moravy 10:13 ↗
Um we actually have wings with leading edge that can move up to 80°.
Henry Catchpole 10:17 ↗
Um get in there and look at it.
Lars Moravy 10:19 ↗
And those wings, you know, can really redirect the air flow underneath up or down or underneath the car, which we can talk a little bit about later. But on the sides, we can come around here. Every little panel that looks like it doesn't move does move.
So, this is actually a barge board. It's not a fender and it'll pop out. Um, and you know, then we get a lot of active flow here, which you'll see on some cars where they put that into the design, right? But we really wanted this transforming character of the vehicle and um maybe we should just transform the whole thing.
Henry Catchpole 10:53 ↗
You can see them all.
Oh, wow.
Lars Moravy 10:55 ↗
So, there's the barge boards going out. There's the vent coming here. And if you look down in it, you can see the cooling fan module right there with the duct sort of coming up.
Henry Catchpole 11:03 ↗
This is the first time I've seen these all moved. No, that was a genuine...
Lars Moravy 11:07 ↗
And you got to hold some things for surprise, Henry. So, it's all very clean to get the airflow moving, right? But then you get the real piece there is this wing back here.
Henry Catchpole 11:17 ↗
I'm trying to sort of think. I thought it was going to turn into something that was actually, I say ugly but kind of, but when you sometimes when you get moving body parts you said it's kind of oh well it looked cool kind of when but then but this actually looks it doesn't ruin the lines at all.
Lars Moravy 11:33 ↗
Yeah, absolutely. It just kind of adds a bit more...
And by hiding all that aero under there, we're still able to keep it like in a very low drag mode when we're not using it. You know, we can close it up front, dam it, so that we get really low drag and force air around. But when we want the air to move, we now have, you know, like I'll say about a third of a square meter of air flow space between here and the side is just to push the air out, which is like means the front like this whole front section, which looks innocuous, it's just a massive wing.
Henry Catchpole 12:02 ↗
Yeah.
Lars Moravy 12:03 ↗
With a lot of air, like 1, 2, 3, 4, 5, five different surfaces, I believe.
Henry Catchpole 12:08 ↗
So have you got any, again I feel like we're burying the lead here but kind of, but as a sort of conventional aero, have you got any figures for kind of like how much kind of downforce it's creating?
Lars Moravy 12:21 ↗
Yeah. With the wing itself like you know obviously it varies with speed. Yeah. Right. So like when we're going you know over 200 miles per hour we can create you know up to 2gs of downforce with this system. But the problem is that doesn't, you know, also work when you're like say below 50 or something miles per hour.
So there's another aero feature. It's going around back and one of the inspirations for this vehicle. Um, you know, my boss has a spy car from a certain film. And you may remember that car had four propellers in the back. We have four fans that are actually based off the same high voltage compressor motor that we have in our heat pump and our thermal system. Each one of these can do maybe 20 kW whereas our base compressor motor was 12 kW which means we, you know, we pull like a lot of force out here but what are they doing?
Henry Catchpole 13:11 ↗
Yeah.
Lars Moravy 13:11 ↗
Well in order to break the laws of physics that we exist around in vehicle dynamics today which are tires you need to like increase traction. Rubber is only good for you know a certain amount of mu doesn't get much above one.
Henry Catchpole 13:25 ↗
Yeah.
Lars Moravy 13:26 ↗
And um in order to do that what we created is a what we call a sucker system. These fans when we drop skirts on the side like the show. So they have skirts in...
Henry Catchpole 13:33 ↗
The skirts come down.

52 more exchanges in this transcript

Sign in free to read the rest of this interview. No card required.

Sign in to read the full transcript

Cite this transcript

APA, MLA, BibTeX
APA

Moravy, L. (2026, October 16). The FLYING Tesla Roadster explained by the man who engineered it [Interview transcript]. Hagerty. CEOInterviews.AI. https://ceointerviews.ai/interview/3081096/

MLA

Lars Moravy. "The FLYING Tesla Roadster explained by the man who engineered it." Hagerty, 16 Oct. 2026. Transcript, CEOInterviews.AI, https://ceointerviews.ai/interview/3081096/.

BibTeX
@misc{moravy2026_3081096,
  author       = {Lars Moravy},
  title        = {The FLYING Tesla Roadster explained by the man who engineered it},
  howpublished = {Interview transcript, Hagerty. CEOInterviews.AI},
  year         = {2026},
  month        = {oct},
  url          = {https://ceointerviews.ai/interview/3081096/},
  note         = {Speaker-attributed transcript with timestamps}
}