CEOInterviews.AI
Start App
Lars Moravy
Vice President of Vehicle Engineering, Tesla, Inc.

Inside Tesla’s 2028 Roadster: 1,500 HP, Fan Downforce and Rocket Thrusters?

📅 Oct 16, 2026 MotorTrend Channel 17 MIN 303946 VIEWS 109 SEGMENTS · 2 SPEAKERS
Tesla's VP of Vehicle Engineering, Lars Moravy walks us through the 2028 Roadster’s wild technology: a fan powered downforce system, more than 1,500 horsepower, active aero and cold gas thrusters for the rocket version. Chapters 0:16 - The James Bond Lotus That Inspired the Roadster 1:26 - How the Fan System Creates Downforce 3:54 - Inside the Roadster’s Battery Pack 6:09 - Two Motors, More Than a Megawatt 7:23 - Why the Roadster Is Rear Wheel Drive 8:49 - How the Active Rear Wing Works 10:09 - The Roadster’s Vehicle Dynamics System 11:13 - Controlling Yaw With Thrust 12:03 - Tesla and Space...

What Lars Moravy said

Written from the verified transcript and checked against it. Every figure links to the moment it was said.

Lars Moravy, Tesla's VP of Vehicle Engineering, discussed the next-generation Roadster, drawing inspiration from Elon Musk's Lotus submarine car. He detailed the active aero system with four deployable fences and fans, claiming over 2 Gs (2,500 kilos) of downforce, enabling theoretical upside-down driving. The fans, based on heat pump components, run at 15,000+ RPM, targeting 20 kW each (80 kW total). The battery pack features a titanium top cover, 900-volt architecture, bespoke 4680 cells with aluminum cans, and dual-sided cooling, enabling over 500 kW charging (10-80% in 10-15 minutes) and over 300 miles range. The rear motor, smaller than Plaid's, produces over a megawatt (500 kW each) with almost 3x power density improvement, offering 1,500 horsepower and 1,348 Nm torque. The car is rear-wheel drive, built at Roadster Factory Texas. The wing uses Optimus ankle motors. The cold gas thruster system uses a 10,000 PSI carbon-overlaid tank, producing 80,000 newtons of thrust (like an F-16 pre-afterburner), with SpaceX collaboration. The rocket version will have three times the cold gas for longer thrust.

Key takeaways

  1. The Roadster's active aero creates over 2 Gs of downforce (2,500 kilos), theoretically allowing upside-down driving.
  2. The rear motor delivers over a megawatt (500 kW each), with 1,500 horsepower and 1,348 Nm torque, a nearly 3x power density improvement over Plaid.
  3. The battery system supports over 500 kW charging, achieving 10-80% in 10-15 minutes, with over 300 miles of range.
  4. The cold gas thruster system produces 80,000 newtons of thrust, comparable to an F-16 without afterburner, and the rocket version will have three times the cold gas.
  5. The Roadster will be built at Roadster Factory Texas (RFTX) on the Giga Texas campus, using cells made at Tesla's California pilot plant.

Numbers and commitments

FigureWhat it refers toTypeAt
2 Gs Downforce generated by active aero system metric 1:39
2,500 kilos Downforce in kilograms metric 1:39
15,000 RPM Fan speed metric 3:21
20 kW Target power per fan metric 3:21
80 kW Total power from four fans metric 3:21
900-volt Battery system voltage metric 3:56
500 kW Charging rate metric 4:48
10 to 15 minutes Charge time for 10-80% timeline 4:48
300 miles Range metric 5:32
1,500 horsepower Power output metric 6:55

Chapters

  1. 0:00Lotus submarine inspiration
  2. 1:16Active aero and downforce
  3. 3:48Battery pack and charging
  4. 5:58Motors and powertrain
  5. 7:09Rear-wheel drive and traction
  6. 8:20Manufacturing locations
  7. 8:39Wing design and Optimus motors
  8. 11:04Thruster system and SpaceX collaboration
  9. 13:52Cold gas vs rocket version

Questions asked in this interview

12
  1. 2:58just the last question on the vents: the fences, is that like a Harrier, like the way the thrust is diverted?
  2. 3:48What are we looking at here?
  3. 4:46Hot in on this side, right?
  4. 5:52Range from what? From 20 to 80?
  5. 7:09Why rear and not all-wheel drive?
  6. 8:01Oh, anything else in the pack?
  7. 8:22Where's Roadster going to be made?
  8. 10:41did you ever think about doing a split wing, like we've seen those?
  9. 11:50I forgot to ask Franz, whose idea was this?
  10. 12:45Like a carbon-fiber scuba tank, right?
  11. 13:52What does cold mean? How cold is it?
  12. 15:02Is it a color? Is there a plume?
Interviewer 0:00 ↗
All right, so we actually got some bonus time with Lars Moravy. Let's just call him the lead technical genius here at Tesla. This is the piece that actually Franz probably should have spoken to, but...
I know this car as the vehicle that was in a very famous James Bond movie. I think you guys are not supposed to talk about that, but this is the Lotus that converts into a submarine.
Lars Moravy 0:29 ↗
That's right. It is a submarine.
Interviewer 0:30 ↗
It is a submarine.
Lars Moravy 0:31 ↗
And like this is, you know, Elon owns this car, so this is his car, so we were able to get it. But like there was a lot of things he loved about it, and you know, there's a lot of aspects about it that made it into the Roadster. I think for me the rear end is kind of the coolest.
Interviewer 0:44 ↗
Okay.
Lars Moravy 0:44 ↗
So if we come around, you kind of look at it. It's cool because it actually works, like the rudders move and...
Interviewer 0:50 ↗
Dive planes. Dive planes. Come on.
Lars Moravy 0:52 ↗
Right. Oh, here are the rudders. But you look back here, it's got four propellers.
Interviewer 0:56 ↗
Okay.
Lars Moravy 0:57 ↗
And when you get down low and you see the propellers, they kind of look like, you know, our four fans, that are creating all that downforce, you know, and this, like the rudders still move back here. And, you know, it's just a really cool piece. But sometimes when you have a, you know, unique design like this and science fiction gives us a little bit of inspiration to make it real.
Interviewer 1:16 ↗
Just on that, because we have them here, I was very struck, and I talked to Franz a little bit about this. You have fans in the car, and he told me about them before I saw it, and I was like, 'Oh, like a McMerc Marlin, it's running around.' But your fans are... or those are like straight down, like sucking straight up. Yours are angled backward, rearward, and up, and you're using fences.
Lars Moravy 1:39 ↗
Yeah. So we have like four fences, like two on the side and two in the... one in the front, one in the rear. And they're kind of... they're mounted and deployable. So when you're not using them, they're up and they come down, and then that gives them some compliance. But what that does is it allows us to create like over 2 Gs of downforce, so like 2,500 kilos or something of downforce, so that, you know, we could theoretically do the old F1 thing upside down without moving.
Interviewer 2:05 ↗
Okay. 2 Gs of downforce.
Lars Moravy 2:08 ↗
Because, you know, one G against gravity and then one G to...
Interviewer 2:11 ↗
Hold the car up. So what he's saying, Lars is claiming Roadster in the thrust version...
Lars Moravy 2:18 ↗
Well, really performance...
Interviewer 2:19 ↗
Oh, performance version. Performance could drive upside down.
Lars Moravy 2:22 ↗
Theoretically. Theoretically, we haven't tried it yet.
Interviewer 2:24 ↗
Okay. Haven't tried it yet. The math says...
Lars Moravy 2:26 ↗
The math says it could.
Interviewer 2:27 ↗
The math says it's possible.
Lars Moravy 2:28 ↗
But you know, that I mean, that comes from all that force. And then when we... because we have the fences, there's actually a dual mode there. We can lift the front and rear fence, and so like we fill in that sort of aero void for active aero in the low speed with the suction. Then when you go high speed and the wings and everything take over, then you can lift the front and rear fence and create like massive airflow underneath and create like a venturi effect. So you suck the air underneath and then it turns into like a little bit of thrust, but mostly just getting that speed of the air moving underneath to balance the airflow on top from the wings.
Interviewer 2:58 ↗
That's some real race car stuff. That's Formula 1 technology. I mean, is... just the last question on the vents: the fences, is that like a Harrier, like the way the thrust is diverted?
Lars Moravy 3:11 ↗
Yeah, it's a little bit like the Harrier where they fly up and they kind of push it down, but like we have ducts there and the ducts kind of are sucking up. And then they kind of exhaust out the back.
Interviewer 3:21 ↗
Got it.
Lars Moravy 3:21 ↗
Each one of those is like, you know, each one of the fans... each one of the fans is based off of our heat pump, compressor, motor, and inverter. Those run about 12 kW. We've kind of sped them up, so we're running a little over 15,000 RPM. And we kind of tweaked the inverter so we can get hopefully up to 20 kW. Still working through that, but that means you get like 80 kW of power from those fans.
Interviewer 3:42 ↗
Okay. All right. So this is a powertrain.
Lars Moravy 3:45 ↗
Yeah. So let's get you on this side. So from...
Interviewer 3:48 ↗
Super exotic, what the heck is that? This is something a little bit more familiar to the regular Tesla enthusiast. What are we looking at here?
Lars Moravy 3:56 ↗
Yeah. So I mean, we love our kind of base layout for architecture. The low CG comes from the battery pack in the floor. This is the battery pack under the floor. But we've gotten a little bit creative with how we do this. So there's kind of two or three unique features in the pack that I want to call out. One is like we went with a titanium top cover purely for mass. It's thinner, it's lighter. Normally we use steel on that to protect on the heat side. The other two things are it's a, you know, it's a 900-volt system, or 800 to 1,000-volt system, and we're using our own 4680s, which actually we developed bespoke for this with a custom chemistry, but also aluminum cans to save mass and improve heat and thermal conductivity. So if you come up here, we're actually dual-sided cooling, and we have... normally we have U-flow where it kind of goes back and forth, but here we're just going one way.
Interviewer 4:46 ↗
Hot in on this side, right?
Lars Moravy 4:48 ↗
And you know, bottom out... or like cool, sorry, cool in on this side and hot out on the other side. So you see in between each bandolier or each set of cells, there's a coolant tube on either side. That's unique for Roadster. So normally we have one down the middle for two sets of cells. And this allowed us to pack them a little more densely, but also get more thermal efficiency, which is how we can get all the power out that those two motors back there need, but also how we get super fast charge rates. So we can charge up over 500 kW on this system. And that's how we get to like the 10 to 80 times hopefully in on the order of 10 minutes, certainly under 15 minutes, which is going to be super cool.
Interviewer 5:25 ↗
Sorry. Sorry. How many... how many cells? This is kilowatt... kilowatt-hours?
Lars Moravy 5:32 ↗
Ish. We're still kind of finalizing the cell chemistry. So it could be a little less or a little more, but we think that's the right number because that'll give you, you know, a bunch of endurance time to go, you know, around the track or around any of the courses that you might run. But also, you know, over 300 miles, and then with that 10 to 12-minute charge time, you're back out there and doing it again.
Interviewer 5:52 ↗
Over 300 miles of range and a 10 to 12-minute charge. Range from what? From 20 to 80?
Lars Moravy 5:56 ↗
10 to 80.
Interviewer 5:57 ↗
10 to 80. Yeah. Okay.
Lars Moravy 5:58 ↗
Great. So then the power conversion comes from the DC pack, goes through our power conversion system here, converts it to high voltage, comes up to our inverter... well, takes the high voltage DC, comes up to our inverters here, and then goes into our bespoke motors. Now we did use some of the technology we used in Plaid here. They're carbon overlaid, but we've got more power-dense rotor material. So we're not using just a typical electrical steel. We're also putting cobalt in it. So we get a lot of power density in this motor. This motor, even though it's smaller than a Plaid motor and actually doesn't have three, has more torque and power than all three Plaid motors combined. It's over a megawatt back here, you know, 500 kW from each motor. Then you have a planetary gear set comes out on either side, and that's the reduction there. So this, even in this size, like the size of the motor is smaller than Plaid, it's more power-dense. So overall we get, you know, almost a 3x improvement in power density.
Interviewer 6:51 ↗
Okay.
Lars Moravy 6:52 ↗
Which is pretty insane.
Interviewer 6:53 ↗
Megawatt. Over a megawatt.
Lars Moravy 6:54 ↗
Over a megawatt.
Interviewer 6:55 ↗
I have to... I hate because I asked you this before and... 1,500 horsepower. 1,500 horsepower. Torque?
Lars Moravy 7:01 ↗
Torque. So if we're at... so torque is 1,348 Newton-meters, which is going to be over 1,000-ish foot-pounds.
Interviewer 7:09 ↗
Okay. Thank you for breaking it down for the traditional. But why rear-wheel drive? Why rear and not all-wheel drive?
Lars Moravy 7:18 ↗
I mean, I think, you know, as a driver's car, I think you can relate. Rear-wheel-drive cars are super fun, but also one of the things we really focused on was like using other rules of physics to get traction. You know, with the sucker system and the downforce from the aero system, we can put all the power through the rear wheels and still get ridiculous acceleration times and ridiculous control, and then also, you know, use the sucker in turning to hold the car in, get over 2 Gs of cornering power or something like that, and then power out. And like to be honest, you know, it's fun to drift and it's fun to have rear-wheel drive and all that power behind you. It's like American muscle, right?
Interviewer 7:53 ↗
Right. Okay. So I'm picking up on some internal Tesla lingo. The fans, you're calling sucker, sucker, sucker.
Lars Moravy 7:59 ↗
Yeah. Very technical term.
Interviewer 8:01 ↗
Very technical term. It's great. Suck. The sucker system. Combined with a megawatt of power, 1,500-ish horsepower, plus the downforce. Oh, anything else in the pack?
Lars Moravy 8:09 ↗
I'm sure... titanium top cover, the spoke cells, aluminum cans, single... double coolant tubes per battery. So a lot of cooling power.
Interviewer 8:18 ↗
Cells are made...
Lars Moravy 8:20 ↗
These are going to be made in California at our pilot plant.
Interviewer 8:22 ↗
Pilot plant. Okay. Very cool. Where's Roadster going to be made?
Lars Moravy 8:26 ↗
It's going to be made at the Giga Texas campus. It has its own building. It's called, you know, RFT, Roadster Factory Texas.

54 more exchanges in this transcript

Sign in free to read the rest of this interview. No card required.

Sign in to read the full transcript

Cite this transcript

APA, MLA, BibTeX
APA

Moravy, L. (2026, October 16). Inside Tesla’s 2028 Roadster: 1,500 HP, Fan Downforce and Rocket Thrusters? [Interview transcript]. MotorTrend Channel. CEOInterviews.AI. https://ceointerviews.ai/interview/3093499/

MLA

Lars Moravy. "Inside Tesla’s 2028 Roadster: 1,500 HP, Fan Downforce and Rocket Thrusters?." MotorTrend Channel, 16 Oct. 2026. Transcript, CEOInterviews.AI, https://ceointerviews.ai/interview/3093499/.

BibTeX
@misc{moravy2026_3093499,
  author       = {Lars Moravy},
  title        = {Inside Tesla’s 2028 Roadster: 1,500 HP, Fan Downforce and Rocket Thrusters?},
  howpublished = {Interview transcript, MotorTrend Channel. CEOInterviews.AI},
  year         = {2026},
  month        = {oct},
  url          = {https://ceointerviews.ai/interview/3093499/},
  note         = {Speaker-attributed transcript with timestamps}
}